cannot set write reliability parameters, WR_REL_SET in this device is read only

BellamyParker

i have G355H bootloop can't go to recovery...but it posible to mode download...
then i try to flash odin and fail...try 4 firmware still failed...

then i try to direct..smart report shown red report..than i update it...
board G355H v1...after dump file use v1 it show success..but device is dead..
i try to repair again smart report is good..update again..factory...then go to tab partioning
write partioning...failed..

it show
cannot set write reliability parameters, WR_REL_SET in this device is read only
partitioning OTP done ..FAILED...

what should i do...now devices dead..but still able to direct identity.. good result

madgoeslim

BellamyParker Hi, please make post problem with details log or screenshot. If you want to attach picture, kindly check at this post how to did that.
B.R

eross

BellamyParker u do not need to repartitioning, n also check CLK resistor, try to make bypass

MizanurRahmanBishal

madgoeslim Set write reliability setting... Cannot set write reliability parameters, WR_REL_SET in this device is read-only.
Could not write 1F to EXT_CSD[167]
Set OTP Partitioning setting completed... failed !

hafiz4saqib

madgoeslim
Hi, I have OALE_X2 with dead condition.
If I use external Power supply to try turn on its wont work.
If I press power button then needle go little further from zero to 0.10 from amplifier section, If I release power button then needle go on zero again.
Even I cant do re partition.

OALE_X2

Same error was showing in Lenovo A916
How to resolve this error ?

BellamyParker

eross thank;s mr eross

MizanurRahmanBishal

Set write reliability setting... Cannot set write reliability parameters, WR_REL_SET in this device is read-only.
Could not write 1F to EXT_CSD[167]
Set OTP Partitioning setting completed... failed !

shankar

MizanurRahmanBishal emmc bad helth change new one.

madgoeslim

hafiz4saqib Hello,
As you can see from the log above, repartitioning is not supported by SAMSUNG chip, because they made the attribute as READ ONLY.
Above procedure is only applies to Hinyx and Kingston chip, CMIIW.
For Samsung chip, you can try to make upgrade FFU if possible.

hafiz4saqib

madgoeslim
If SAMSUNG emmc have READ ONLY attribute then could you guide me that how to repair MOBILE HANG ON LOGO,EMMC READ ONLY or DEAD MODE ????

madgoeslim

hafiz4saqib

madgoeslim For Samsung chip, you can try to make upgrade FFU if possible.

Or replace it by new one.

rohitkumar

solution pls this error

shusil

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8842-6199
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 48MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: FN12AB (0x464e31324142), rev: 0x00, serial number: 0x60C9D4D5
Manufacturing date: Jun 2017
CID: 15010046 4E313241 420060C9 D4D5644E
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.7 (MMC v5.0, v5.01)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 7.28 GiB(7,818,182,656 bytes)

Writing eMMC partition settings...
Set general purpose partition... Done
Set write reliability setting... Cannot set write reliability parameters, WR_REL_SET in this device is read-only.
Could not write 1F to EXT_CSD[167]
Set OTP Partitioning setting completed... failed!

Jibachh

Cannot set write reliability parameters, WR_REL_SET in this device is read-only.
Could not write 1F to EXT_CSD[167]

Jibachh

platform: MT6735, cpu abi: armeabi-v7a
manufacturer: HUAWEI
board: LUA-L21, name: LUA-L21
brand: HUAWEI, model: HUAWEI LUA-L21 ()
build model list: HUAWEI LUA-L21 ()
build id: HUAWEILUA-L21, version: 5.1 Lollipop (LUA-L21C328B102)
build description: LUA-L21-user 5.1 HUAWEILUA-L21 1462465253 release-keys

Internal storage: 3.95 GiB
crypto state: unencrypted
eMMC 5.x HEALTH report:
Device lifetime: Urgent (Consumed 90% of the reserved block)
Estimation of the device lifetime (SLC): Exceeded its maximum estimated device life time
Estimation of the device lifetime (MLC): Exceeded its maximum estimated device life time
Selected: [SAMSUNG] KMFN10012M/8GB (BGA221)