hi,i want to use factory image with full scater firmware(h30-u10) but after afew seconds it shows this error,even i changed vcc,and vccq voltage,but nothing changed , mean while when i want to use on the board without dump it error 4032 sp flash tools 
Connection status: EHCI:HUB:HUB[#2]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-3997
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.0 V, VCCQ: 1.8 V
Bus: 4 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H8G2d (0x483847326404), rev: 0x03, serial number: 0x09092532
Manufacturing date: Oct 2013
CID: 90014A48 38473264 04030909 2532A096
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4 MiB
Boot2: 4 MiB
RPMB: 4 MiB [Authentication Key not yet programmed]
User area: 7.28 GiB(7,818,182,656 bytes)
Current partition access:
Access to boot partition 1
Writing PRELOADER at 0x00000000 (221 sectors)... Done in 0.074 s
Setting boot partition config to 0x48... Done
Failed to initialize eMMC (return code: 6, CMD Error: Invalid Voltage Range) !!!
CMD1 error, cmd response: 0x40FF8080, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
Current partition access:
Access to user area
Processing file: "MBR-sign"...
Writing MBR at 0x00000000 (34 sectors)... Failed to write block 0x00000000:0 (return code: 0, CMD Error: )
cmd response: 0x0, card status: 0x0, card state: 0 (Card is in unknown state)
OS error code: 0x00000079(The semaphore timeout period has expired)
Connection status: EHCI:HUB:HUB[#2]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-3997
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.0 V, VCCQ: 1.8 V
Bus: 4 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H8G2d (0x483847326404), rev: 0x03, serial number: 0x09092532
Manufacturing date: Oct 2013
CID: 90014A48 38473264 04030909 2532A096
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4 MiB
Boot2: 4 MiB
RPMB: 4 MiB [Authentication Key not yet programmed]
User area: 7.28 GiB(7,818,182,656 bytes)
Cache size: 512 KiB
Partition configuration: 0x48
Boot acknowledge is sent during the boot operation
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Selected: [HYNIX] eNAND H26M42003GMR/8GB (BGA153)
please help me,thank you
