EMMC check problem

aungthuwin

I check Skhnix BGA221. I receive this error. How to check setting.

madgoeslim

aungthuwin which error?

Chennai

madgoeslim hi bro

aungthuwin

I do scren shoot for post. How can I upload?. I would like to show my error.

madgoeslim

aungthuwin See here how to insert image

aungthuwin

My EMMC BGA221 check erro

I checked new emmc BGA221 but i received this error. Which setting need to do. Guide me please.
error

madgoeslim

aungthuwin Auto setting is enough when using eMMC Adapter. But if you using new adapter, you can try this tips.

elmahdy11

aungthuwin

https://www.youtube.com/watch?v=zKTFd99raiI

AnshulAgrawal

aungthuwin open bga 221 emmc socket and clean connection with pcb repack then work fine

aungthuwin

madgoeslim Thank for you custome care

Oxi

Your EMMC is broken

MohdFarisIzzat

im also face the same problem, how to solve?

Deepakgarg

MohdFarisIzzat https://ufixers.com/d/101-new-ufi-emmc-adapter-not-properly-connected

klemat

hello .. im new in ufi box user... today my box cant detect any emmc connected... insertion test done.. but it always failed to initialize emmc
i tried to decrease clock speed and bit connection.. but it still failed....

is there any solution

Deepakgarg

klemat if you can post log or screenshot that will make it easy to understand your problem

klemat

using kmvtu as sample

Connection status: EHCI:HUB:HUB:USB 2.00 High-speed
Interface: UFI High-Speed
Serial number: 0011-8839-xxxx
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Failed to initialize eMMC (return code: 20, CMD Error: Invalid response) !!!
CMD1 error, cmd response: 0x3FE040F, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
--- Try to use 1 bit connection ---
Check your connection, make sure eMMC inserted properly.

i try to decrease the vccq until 1.8v to make the emmc detected...

Connection status: EHCI:HUB:HUB:USB 2.00 High-speed
Interface: UFI High-Speed
Serial number: 0011-8839-xxxx
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 8 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: VTU00M (0x56545530304d), rev: 0xFC, serial number: 0xF3247CFE
Manufacturing date: Apr 2014
CID: 15010056 54553030 4DFCF324 7CFE4138
CSD: D0270132 0F5903FF F6DBFFFF 8E40406C
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 2048 KiB
Boot2: 2048 KiB
RPMB: 128 KiB
User area: 14.68 GiB(15,758,000,128 bytes)
Cache size: 64 MiB
Partition configuration: 0x00
No boot acknowledge is sent (default)
Device is not boot-enabled (default)
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
User area write protection: 0x50
Password protection features: enabled
Power-on write protection: possible
Permanent write protection: not possible
Lock status: not locked
Selected: [SAMSUNG] moviNAND KMVTU000LM-B503/16GB (FBGA153)

but.. with that voltage... i cant program it.. ex: write a firmware
Connection status: EHCI:HUB:HUB:USB 2.00 High-speed
Interface: UFI High-Speed
Serial number: 0011-8839-xxxx
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 8 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: VTU00M (0x56545530304d), rev: 0xFC, serial number: 0xF3247CFE
Manufacturing date: Apr 2014
CID: 15010056 54553030 4DFCF324 7CFE4138
CSD: D0270132 0F5903FF F6DBFFFF 8E40406C
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 2048 KiB
Boot2: 2048 KiB
RPMB: 128 KiB
User area: 14.68 GiB(15,758,000,128 bytes)

Re-partitioning... Done.
Writing MBR, GPT at 0x00000000-0x000043FF (34 sectors)... Failed to write block 0x00000000:17408 (return code: 2, CMD Error: CMD CRC fail)
cmd response: 0x19000009, card status: 0x19000000, card state: 0 (Card is in unknown state)
status: A sequence or password error has been detected in lock/unlock card command
Writing boot partition config to 0x48... [179]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
Done.
Writing preloader header... Done.
Current partition access:
Access to boot partition 1
Writing preloader at 0x00000000 (320 sectors)... Failed to write block 0x00000000:65536 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
Operation canceled by user request.
Setting boot config...
Writing boot partition config to 0x48... [179]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
Done.

Deepakgarg

klemat try vcc 2.8v
also try firmware update and nand test

WenkzDarmawan

klemat ,i'm in indonesia darmawan cell from Bekasi. Im permission to joint group ufixers.
Im understand direct emmc samsung g532, j2 prime in ufi identify log Failed to initialize eMMC (return code:0, CMD error🙂!!!
Any solution to prublem brow...???
Im newby.. Thanks u.

WenkzDarmawan

klemat

Emmc ffu done... Although it takes three times of TP
Nand test .. Failed... But i try to test it in my friend box.. The emmc works normally..sorry cannot post log right now

Even.i tried to update the box firmware.. But the result is still the same...

One more thing... Since i bought this box a week ago.. My box cannot detect hynix... :confused...

klemat

problem solved... put a little caplang on the socket .. and press the pcb and release it... i do it repeately for about 30 minutes..

Arjun5259

Better to use MOORC emmc socket and click direct emmc isp and enjoy 😎

IcaGsm

Correct reading, writing error with the adapter and in direct emmc (IPS)
READING OK:
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x05, serial number: 0x02A2ED9B
Manufacturing date: dic 2014
CID: 90014A48 34473164 040502A2 ED9BC14E
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 3.64 GiB(3,909,091,328 bytes)
Cache size: 512 KiB
Partition configuration: 0x00
No boot acknowledge is sent (default)
Device is not boot-enabled (default)
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
Selected: [HYNIX] eNAND H9TP32A4GDBCPR-KGM/4GB (FBGA162)

WRITING ERROR:
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x05, serial number: 0x02A2ED9B
Manufacturing date: dic 2014
CID: 90014A48 34473164 040502A2 ED9BC14E
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 3.64 GiB(3,909,091,328 bytes)

Loading file: "\%BACKUPS%\LGE\LG-D390(KTU84P-4.4.4-KTU84P)[H9TP32A8JDACPR-KGM_0AA25CA7]\ext_csd.bin", size: 512 bytes...
Writing extcsd, 512 bytes... Done.
Failed to initialize eMMC (return code: 6, CMD Error: Invalid Voltage Range) !!!
CMD1 error, cmd response: 0x40FF8080, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.

ProOFF

Set both voltages to "auto". Try to do a "nand test."
According to the program report, you can see that you are using "isp mode". Insert the emmc into the adapter, turn off the "isp mode". Try writing

IcaGsm

NAND test
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x05, serial number: 0x02A2ED9B
Manufacturing date: dic 2014
CID: 90014A48 34473164 040502A2 ED9BC14E
CSD: D0270132 0F5903FF FFFFFFEF 8A4040D2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 3.64 GiB(3,909,091,328 bytes)

Current partition access:
Access to boot partition 1
Writing random bytes to boot1, sector: 7044... Done in 0.007 s
Verifying... Done in 0.002 s, content verified successfully.
Current partition access:
Access to user area
Writing random bytes to userarea, sector: 1690337... Done in 0.004 s
Verifying...
Verify failed at 0x3395C200: file data [ 55 53 45 52 ], device data [ 00 00 00 00 ]
NAND storage "userarea" partition test failed !

Deepakgarg

IcaGsm your emmc seems bad need replacement