EMMC check problem: Page 4 - UFIXERS Community

EMMC check problem

Vikas

i have allso same problam solution plz

Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-6940
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 8 bit (HS SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: GD6BMB (0x474436424d42), rev: 0x01, serial number: 0x98C0D81C
Manufacturing date: Feb 2018
CID: 15010047 4436424D 420198C0 D81C2592
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 29.12 GiB(31,268,536,320 bytes)

Reading modem at 0x04000000-0x093FFFFF size: 84 MiB... Failed to read block 0x05400000:0 (return code: 1, CMD Error: Timeout)
cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
--- Try to decrease the clock speed ---
--- Make sure the connection between BOX and eMMC stable ---
--- please try again (you may RESUME the read process) ---

madgoeslim

Apu boot size and rpmb resize option

This option is available for samsung chip only.

Vikas --- Try to decrease the clock speed ---
--- Make sure the connection between BOX and eMMC stable ---
--- please try again (you may RESUME the read process) ---

Apu

hello sir.this is onportent problem my boot size and rpmb resize option not showing and how to solve please fix this problem

Mbpreem

madgoeslim clock speed

GsmHamid

H9TP32A4GDBCPR-KGM this emmc bga number / test point need

madgoeslim

GsmHamid H9TP32A4GDBCPR-KGM

Hi,
This is hinyx chip, ffu for this kind of chip is not supported, so testpoint is also not available.

Aryan

Connection status: EHCI:HUB:HUB[#5]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-3997
Boot version: 1.04, FW version: 1.14 (Aug 25 2021 04:56:05)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 3MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G2b (0x483447326211), rev: 0x01, serial number: 0x4210B94F
Manufacturing date: Apr 2016
CID: 90014A48 34473262 11014210 B94F438A
CSD: D07F0132 0F5903FF FFFFFFEF 8A4040DA
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4 MiB
Boot2: 4 MiB
RPMB: 4 MiB [Authentication Key not yet programmed]
User area: 3.64 GiB(3,909,091,328 bytes)

Current partition access:
Access to boot partition 1
Writing random bytes to boot1, sector: 0... Failed to write block 0x00000000:1024 (return code: 1, CMD Error: Timeout)
cmd response: 0xB00, card status: 0x0, card state: 5 (Card is sending an operation)
status: unknown (0)
NAND storage "boot1" partition test failed!

Benoa

nsertion test... CLK not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 6, CMD Error: Invalid Voltage Range) !!!
CMD0 error, cmd response: 0x40FF8080, card state: 255 (Card is in unknown state)
GO_IDLE_STATE command failed.

Benoa

![](https://)good evening sir, I ask for an explanation when I have a problem for oppo a3s totally dead and detected 9008 I tried to use the direct method via ufi box but there was a problem when direct to ufi always failed cmd 6 even though the jumper to the pcb board isp point is already good but why is it still I haven't been able to detect it on UFI, it always fails. Please enlighten me, sir, thanks

greatelias

Benoa had same device, tried and failed,decided to take emmc down carefully since its glued,later realized it was 90% consumed,

suntrix

WenkzDarmawan hey bro please tell me ("Failed to initialize eMMC (return code: 0, CMD Error: ) !!! How to solve this eror kindly 😊

madgoeslim

suntrix Failed to initialize eMMC (return code: 0, CMD Error:

Please post your problem with details log or screenshot for further assistance.

« Previous Page