Meizu Pro 7-H and Android ToolBox

smtel

Hello! does Android ToolBox work with meizu pro 7-h? I have error when identify. As I see from logs this CPU is not supported?

https://cdn1.savepice.ru/uploads/2018/3/27/35a3fa59a5b40f7df6bcb885b5df7ff6-full.jpg

madgoeslim

smtel Please change model to M1792L(PRO 7), and do Identify Device again. Post result here.

smtel

Unfortunately, the device is not on hand, because it has been almost two months, the client will not wait that long...

Sardor

не всё ровно такая ошибка

Sardor

all exactly such an error
AUTH info: MEIZU, version: 0
BROM version[1]: 7.1625.3.0
Loading DA: MTK_AllInOne_DA.bin (4.31 Mi😎
version: 3.3001.00.00, start addr: 0x40000800
Connecting to BootROM...
Power off the phone, disconnect and reconnect the battery(if possible) and connect USB cable...
Hold the VOL DOWN to force MediaTek BootROM.
Scanning BootROM or Preloader port... Done.
Detected MediaTek USB Port (COM187)
USB Driver: [MediaTek Inc.] wdm_usb, version: 3.0.1504.0, date: 1-22-2016
Connecting Bootrom... failed
Error: -1073348603 (STATUS_BROM_CMD_FAIL)
BROM_SCMD_SLA error. code 0x7020

VoTan

Sardor
please choose OEM 21

Sardor

AUTH info: MEIZU, version: 0
BROM version[1]: 7.1625.3.0
Loading DA: MTK_AllInOne_DA[oem_v21].bin (8.09 Mi😎
version: 3.3001.00.00, start addr: 0x40000800
Connecting to BootROM...
Power off the phone, disconnect and reconnect the battery(if possible) and connect USB cable...
Hold the VOL DOWN to force MediaTek BootROM.
Scanning BootROM or Preloader port... Done.
Detected MediaTek USB Port (COM25)
USB Driver: [MediaTek Inc.] wdm_usb, version: 3.0.1504.0, date: 1-22-2016
Connecting Bootrom... failed
Error: -1073348603 (STATUS_BROM_CMD_FAIL)
BROM_SCMD_SLA error. code 0x7020

auth_sv5"oem"

AUTH info: MTK, version: 1
BROM version[1]: 7.1625.3.0
Loading DA: MTK_AllInOne_DA[oem_v21].bin (8.09 Mi😎
version: 3.3001.00.00, start addr: 0x40000800
Connecting to BootROM...
Power off the phone, disconnect and reconnect the battery(if possible) and connect USB cable...
Hold the VOL DOWN to force MediaTek BootROM.
Scanning BootROM or Preloader port... Done.
Detected MediaTek USB Port (COM25)
USB Driver: [MediaTek Inc.] wdm_usb, version: 3.0.1504.0, date: 1-22-2016
Connecting Bootrom... failed
Error: -1073348603 (STATUS_BROM_CMD_FAIL)
BROM_SCMD_SEND_AUTH error. code 0x7009
auth_sv5"oem21

Sardor

because of AUTH or DA not working

Sardor

Connection status: XHCI:HUB3:USB 2.0 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-1551
Boot version: 1.04, FW version: 1.11 (Dec 6 2017 17:13:32)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x15 (Samsung)
Product name: DH6DMB (0x444836444d42), rev: 0x05, serial number: 0xFE05C402
Manufacturing date: июн 2017
CID: 15010044 4836444D 4205FE05 C402643A
CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 58.24 GiB(62,537,072,640 bytes)
Reading PrimaryGPT at 0x00000000-0x00007FFF size: 32 KiB... Done in 0.067 s
File saved to "\%BACKUPS%\Meizu\PRO_7(Flyme_6.1.3.0G-7.0-NRD90M)[DH6DMB_FE05C402]\user_part\PrimaryGPT.img" (CRC32: 0xE93A2A90)
Blank checking: NOT blank
Reading boot_para at 0x00008000-0x00107FFF size: 1 MiB... Done in 2.149 s
File saved to "\%BACKUPS%\Meizu\PRO_7(Flyme_6.1.3.0G-7.0-NRD90M)[DH6DMB_FE05C402]\user_part\boot_para.img" (CRC32: 0x7F5680A1)
Blank checking: NOT blank
Reading recovery at 0x00108000-0x04107FFF size: 64 MiB... cmd response: 0x900, card status: 0x0, card state: 4 (Card is in transfer state)
status: unknown (0)
--- Make sure the connection between BOX and eMMC stable ---
--- please try again (you may RESUME the read process) ---

Reading not working

Viktor54

Sardor Good afternoon. Can you share a dump?

Sardor

In general, there is nothing, there is someone to unlock

ddilshod93

Sardor contact me via telegramm : ddilshod93

Muhammet

Any solution for Pro7 or Pro7-H ?