how to check ram in EMMC

GsmHamid

Connection status: EHCI:HUB:HUB:HUB:USB 2.0 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-6685
Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 1 bit (SDR 52MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x86, serial number: 0x02A2CDDA
Manufacturing date: Sep 2013
CID: 90014A48 34473164 048602A2 CDDA9072
CSD: D0270132 0F5903FF FFFFFFE7 8A4040E2
EXT_CSD revision: 1.5 (MMC v4.41)
Partition info:
Boot1: 2048 KiB
Boot2: 2048 KiB
RPMB: 2048 KiB
User area: 3.61 GiB(3,875,536,896 bytes)
Partition configuration: 0x00
No boot acknowledge is sent (default)
Device is not boot-enabled (default)
Partitioning support: 0x03
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
Selected: [HYNIX] eNAND H9TP32A8JDACPR-KGM/4GB (BGA162)

madgoeslim

GsmHamid
Hello,
If you means check the condition of RAM inside the eMCP by eMMC ToolBox, so there is non of them have such function.

MrSuraj

GsmHamid JOIN OUR ONLINE CLASS YOU WILL GET FULL INFORMATION ABOUT EMMC AND PROGRAMMING KNOWLEDGE , ANY KIND OF DEAD YOU CAN TURN ON VERY EASILY

GSM_RSPI_RUBEL

GsmHamid hello sir your emmc rom is 4gb and ram is 1gb.bga is 162

anasshe

MrSuraj link plz ?????

GsmHamid

MrSuraj thank u sir

GsmHamid

Connection status: EHCI:HUB:HUB[#3]:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-6685
Boot version: 1.04, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Bus: 4 bit (HS SDR 24MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: H4G1d (0x483447316404), rev: 0x87, serial number: 0x00201201
Manufacturing date: Jan 2014
CID: 90014A48 34473164 04870020 12011150
CSD: D0270132 0F5903FF FFFFFFE7 8A4040E2
EXT_CSD revision: 1.5 (MMC v4.41)
Partition info:
Boot1: 2 MiB
Boot2: 2 MiB
RPMB: 2 MiB [Authentication Key not yet programmed]
User area: 3.61 GiB(3,875,536,896 bytes)

Re-partitioning... Done
Writing MBR, GPT at 0x00000000-0x000043FF (34 sectors)... Done in 1.063 s
Current partition access:
Access to boot partition 1
Processing file: "u-boot-spl-16k.bin"...
Writing splloader at 0x00000000 (64 sectors)... Done in 0.016 s
Current partition access:
Access to boot partition 2
Processing file: "u-boot.bin"...
Writing uboot at 0x00000000 (1008 sectors)... Done in 0.397 s
Current partition access:
Access to user area
Processing file: "prodnv.img"...
Writing prodnv at 0x00100000 (10240 sectors)... Failed to write block 0x00110000:65536 (return code: 1, CMD Error: Timeout)
cmd response: 0xD00, card status: 0x0, card state: 6 (Card is receiving operation information)
status: unknown (0)
solution please..............

mahmoodufi

GSM_RSPI_RUBEL
[Authentication Key not yet programmed]
sir is ka kya matlab hy

GSM_RSPI_RUBEL

mahmoodufi it means this emmc rpmb is clean.this emmc use other devices.