Problem with ISP connection : Page 2

Problem with ISP connection

Jeremmi

Anyone have any luck? Or is there a solution to this problem?
Maybe someone knows other isp connectors for ufi?

mhaghnegahdar

same problem with adapter isp v2

Meon

Connection status: NUSB3HUB:USB 2.0 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8840-1458
Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Failed to initialize eMMC (return code: 0, CMD Error: ) !!!
CMD0 error, cmd response: 0x0, card state: 0 (Card is in unknown state)
GO_IDLE_STATE command failed.
plz h

MeharTanveer

hello team i buy new ufi box and i face the problem with isp adapter i try to connect with 15 phones even 2 phones on but not success please team can u guide me what is the problem

VorugantiGoverdhan

i am also same problem not connect to any phone

ZameerPathan

same problem with adapter isp v2😥😥

harshas669

same problume to me how to solve?

harshas669

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: xxx-xxxx-xxxx
Boot version: 1.04, FW version: 1.10 (jan 15 2019 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 2.8 V
Failed to initialize eMMC (return code: 20, CMD Error: Invalid response) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

keemo

I have same issue i tried all method but my v2 adopter now not ready to connect any device so ufi is there any solution or we should forget our investment with you i don't get any profit yet from this box i was so excited before purchase of this box now i am feeling like victim i am seeing here lot of people have have same issue i am not only one but there is no support solution

Connection status: EHCI:HUB:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8841-0065
Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

Alexid7

if not connect remove emmc and use emmc adopter

leoo

its too hard to remove emmc becouse glue pasted emmc is very hard hard to remove please give as solution for isp adapter what we can change in isp adapter to work right

madgoeslim

leoo
Here's the tip for ISP connection :
--- Make cable jumper as short as possible, 6cm is max
--- Try using USB power, for SoC with active PBL, i.e QC, MTK
--- Uncheck insertion test in setting for uninterupt software init
--- Use 5V DC Usb cable (include in ufibox package) for stable power
Gud Luck to you

« Previous Page