i have vivo y95 having issue logo only
i was try repair with partition but cant success please guide me solve problem
what i do below
1.backup
2.partition
3.erase
4.factory reset emmc
still same Device lifetime: Urgent (Consumed 90% of the reserved block)
[ Open \ISP Pinout picture ]
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8843-0190
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x5129189C
Manufacturing date: Jan 2019
CID: 90014A48 43473861 34A25129 189C16B6
CSD: D0270132 8F5903FF FFFFFFEF 8A400026
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 58.24 GiB(62,537,072,640 bytes)
Cache size: 1 MiB
Hardware reset function: 1
Partition configuration: 0x00
No boot acknowledge is sent (default)
Device is not boot-enabled (default)
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning completed
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
User area write protection: 0x10
Password protection features: enabled
Power-on write protection: possible
Permanent write protection: not possible
Lock status: not locked
eMMC 5.x HEALTH report:
Device lifetime: Urgent (Consumed 90% of the reserved block)
Estimation of the device lifetime (SLC): 0% - 10% device life time used
Estimation of the device lifetime (MLC): 0% - 10% device life time used
Selected: [HYNIX] H9TQ52ACLTMCUR/64GB (BGA221)
Connection status: XHCI:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8843-0190
Boot version: 1.05, FW version: 1.13 (Aug 19 2019 23:46:09)
Insertion test... Done
VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0x90 (SK Hynix)
Product name: HCG8a4 (0x484347386134), rev: 0xA2, serial number: 0x5129189C
Manufacturing date: Jan 2019
CID: 90014A48 43473861 34A25129 189C16B6
CSD: D0270132 8F5903FF FFFFFFEF 8A400026
EXT_CSD revision: 1.8 (MMC v5.1)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 58.24 GiB(62,537,072,640 bytes)
Writing eMMC partition settings...
Device is already partitioned
