Samsung GT-I9060I needed

noomsikharn

Can anyone help share the dump file of GT-i9060i.
I already make the device dead now. Please share should you have it.
Logs:
Connection status: XHCI:HUB3:HUB3:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-3146
Boot version: 1.04, FW version: 1.11 (Dec 6 2017 17:13:32)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
Card/BGA: BGA (Discrete embedded) - High density MMC
Manufacturer ID: 0xFE (Micron)
Product name: P1J95K (0x50314a39354b), rev: 0x13, serial number: 0x5C61B388
Manufacturing date: Dec 2015
CID: FE014E50 314A3935 4B135C61 B388C286
CSD: D07F0132 0F5913FF FFFFFFEF 924000A2
EXT_CSD revision: 1.6 (MMC v4.5, v4.51)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 4096 KiB
User area: 7.28 GiB(7,818,182,656 bytes)
Cache size: 256 KiB
Partition configuration: 0x08
No boot acknowledge is sent (default)
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning completed
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00
Power-on write protection: possible
Permanent write protection: possible
Lock status: not locked
Selected: [Micron] eMMC (JWA60)MT29TZZZ8D5BKFAH-125W/8GB (BGA221)

madgoeslim

noomsikharn Dump files available in support.

noomsikharn

Already tried that dump file (ufi) result in phone dead.
Coz only after have done the job notice that boot size are not the same as prescribed in the logs sir.

noomsikharn

Would be happy sir for the reply
On why dump file below result in phone dead state
Then next time I wouldn't rare come cross again.

EXT CSD info:
EXT_CSD revision: 1.7 (MMC v5.0, v5.01)
Partition info:
Boot1: 4096 KiB
Boot2: 4096 KiB
RPMB: 512 KiB
User area: 7.28 GiB(7,818,182,656 bytes)
Cache size: 64 MiB
Partition configuration: 0x08
No boot acknowledge is sent (default)
Boot partition 1 is enabled for boot
Partitioning support: 0x07
Device support partitioning feature
Device can have enhanced technological features
Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x00
Boot area write protection: 0x00

madgoeslim

noomsikharn try using other emcp chip, like samsung kmr8/kmqn

noomsikharn

Sorry I am doing the job via ISP. Not changing the emmc.

madgoeslim

noomsikharn This is eMCP, just by looking log fine, and testing nand test passed,writing good dump file OK,doesn't mean that emcp is Good. Because emmc tool only detect nand area. And we can't check lpddr inside emcp. So, if you confident that all you have done is right, but phone still can't boot, the other chance is just by retry with other emcp.

noomsikharn

madgoeslim Appreciated reply.
One Question Isn't It matter That
RPMB size of dump file(ufi server) and
Those to Of device's emcp RPMB size are not the same. One is 4MB while other 512KB. Sorry for so Noob.