nokia ta-1029 dead during frp reset via isp point. but there is no image or emmc file for nokia 2 TA-1029 now can you help me and get me out this trouble.. :-( thanks.

    israr Hello,
    Can you post the detail log and screenshot regarding to your problems here?

    • joy replied to this.
        11 days later

        Connection status: EHCI:HUB:USB 2.0 High-Speed
        Interface: UFI High-Speed
        Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
        Insertion test... Done.
        Init bus...
        VCC: 3.3 V, VCCQ: 3.0 V
        Bus: 1 bit (SDR 52MHz)
        Access mode: sector mode
        Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
        Card/BGA: BGA (Discrete embedded) - High density MMC
        Manufacturer ID: 0x15 (Samsung)
        Product name: FN62MB (0x464e36324d42), rev: 0x03, serial number: 0x99E6EE9B
        Manufacturing date: Oct 2017
        CID: 15010046 4E36324D 420399E6 EE9BA484
        CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
        EXT_CSD revision: 1.8 (MMC v5.1)
        Partition info:
        Boot1: 4096 KiB
        Boot2: 4096 KiB
        RPMB: 512 KiB
        User area: 7.28 GiB(7,818,182,656 bytes)

        eMMC 5.x HEALTH report:
        Device lifetime: Normal
        Estimation of the device lifetime (SLC): 0% - 10% device life time used
        Estimation of the device lifetime (MLC): 0% - 10% device life time used
        moviNAND Smart report:
        Error Mode: 0x00000000 (Invalid)
        Smart report in MMC5x has changed and not supported for this device(use eMMC 5.x HEALTH report instead).

        5 months later

        israr
        Just check at support server, there are stock firmware in QFIL format, means this firmware can be use for debrick as well as for full flashing procedure.
        2019-07-23-201300.jpg

        joy ufi not support nokia 3..etc..

        Hello, for nokia 2, 3, 5, 6 if you have stock firmware and correct loader, you can flash it via ufi android toolbox.
        For Nokia newest device, like nokia 3.1, 6.1, and later, need auth by server for flashing in fastboot protocol.
        Will support this in upcoming Ufi update.
        2019-07-20-190207.jpg

              10 days later

              what is the problem!sir,
              Connection status: EHCI:HUB:HUB:USB 2.0 High-Speed
              Interface: UFI High-Speed
              Serial number: 0011-8840-8698
              Boot version: 1.04, FW version: 1.12 (Jun 7 2018 00:06:47)
              Insertion test... Done.
              Init bus...
              VCC: 3.3 V, VCCQ: 1.8 V
              Bus: 1 bit (SDR 3MHz)
              Access mode: sector mode
              Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
              Card/BGA: BGA (Discrete embedded) - High density MMC
              Manufacturer ID: 0x15 (Samsung)
              Product name: CKTM4R (0x434b544d3452), rev: 0x00, serial number: 0x1D1AEA0B
              Manufacturing date: Jul 2017
              CID: 15010043 4B544D34 52001D1A EA0B7422
              CSD: D0270132 0F5903FF F6DBFFEF 8E40400C
              EXT_CSD revision: 1.8 (MMC v5.1)
              Partition info:
              Boot1: 4096 KiB
              Boot2: 4096 KiB
              RPMB: 16384 KiB
              User area: 58.24 GiB(62,537,072,640 bytes)

              Factory erase... failed !
              Reseting PART_CONFIG... [179]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
              failed !
              Reseting BOOT_BUS_CONDITIONS... [177]Failed to Switch (return code: 1, CMD Error: Timeout) !!!
              failed !

              5 days later
              Write a Reply...