what problem on my box?

ChanRattanak

it show like this

Connection status: EHCI:HUB:HUB:USB 2.00 High-speed
Interface: UFI High-Speed
Serial number: 0011-8xxxxxxxxx
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 3.0 V
Failed to initialize eMMC (return code: 226, Over current detected) !!!

Pls help me all user and supporter.

ChanRattanak

VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

ChanRattanak

Now my problem solved by check cmd pin again

Connection status: EHCI:HUB:HUB:USB 2.00 High-speed
Interface: UFI High-Speed
Serial number: 0011-88xxxxxxxxx
 Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Bus: 1 bit (SDR 4MHz)
Access mode: sector mode
Power supply: dual-voltage (1.70-1.95V, 2.7-3.6V)
 Card/BGA: BGA (Discrete embedded) - High density MMC
 Manufacturer ID: 0x45 (SanDisk)
 Product name: SEM08G (0x53454d303847), rev: 0x22, serial number: 0x43510F8E
 Manufacturing date: Jul 2015
CID: 45010053 454D3038 47224351 0F8E72C6
CSD: D00F0032 0F5903FF FFFFFFFF 8A40407E
EXT_CSD revision: 1.6 (MMC v4.5, v4.51) 
Partition info:
 Boot1: 2048 KiB
 Boot2: 2048 KiB
 RPMB: 2048 KiB
 User area: 7.28 GiB(7,818,182,656 bytes)
Cache size: 1 MiB
Hardware reset function: 1
Partition configuration: 0x08
 No boot acknowledge is sent (default)
 Boot partition 1 is enabled for boot
Partitioning support: 0x05
 Device support partitioning feature
 Device cannot have enhanced technological features
 Device partitioning possible
Boot configuration protection: 0x00
Boot bus conditions: 0x02
  Bus width: x8 (sdr/ddr), boot mode: sdr(default), reset bus width to x1 sdr(default)
Boot area write protection: 0x00
 Power-on write protection: possible
 Permanent write protection: possible
 Lock status: not locked
User area write protection: 0x50
 Password protection features: enabled 
 Power-on write protection: possible
 Permanent write protection: not possible
 Lock status: not locked
EXT_CSD backup saved to "\\%BACKUPS%\SEM08G_43510F8E.ext_csd"

ANDROID ROM info:
 platform: hi6210sft, cpu abi: armeabi-v7a
 manufacturer: HUAWEI
 board: BalongV8R1SFT, name: hi6210sft
 brand: Honor, model: 
 build id: KOT49H, version: 4.4.2 KitKat (BalongV100R001C50B311)
 build description: hi6210sft-user 4.4.2 KOT49H eng.jenkins.20151209.184917 test-keys

Selected: [SanDisk] iNAND SDIN8DE2-8G  (FBGA153)

BorNeo

the is my box error ...direck isp

what the problem is adafter chip ?
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 16, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

madgoeslim

BorNeo Already answer by box :
--- Check eMMC pins and connection --- --- Try to select correct VCC/VCCQ manually --- --- Try to decrease the clock speed ---

Andikha

what the problem is adafter chip ?
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

ProOFF

Dead emmc. If emmc Samsung - try testpoint metod.

robin

ProOFF Dead emmc. If emmc Samsung - try testpoint metod

thx for the info

IstiantoCP

my box isp all hand phone
Connection status: EHCI:HUB:USB 2.00 High-speed
Interface: UFI High-Speed
Serial number: 0011-8839-4296
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... Done.
VCC, VCCQ not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 1.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---

ProOFF

Box often works poorly on in-circuit connection. Try to additionally connect the phone to usb to the !!!same!!!! computer, to which the UFI BOX is connected.

Rashidul

Hello UFI-box team

How to SanDisk eMMC write Protection remove?

SivaKumar

Rashidul https://drive.google.com/open?id=0BxuF_fMHsnRTX3QyYlZCaFlOc2M

Fendy

plese hlep me
what happens with this error
please its solution

Failed to initialize eMMC (return code: 0, CMD Error: ) !!!
CMD0 error, cmd response: 0x0, card state: 0 (Card is in unknown state)
GO_IDLE_STATE command failed.

Jamil

Fendy same problem with me

mbah_walang

Fendy me too please help

ProOFF

There are available tested and serviceable memory chips in different cases. If there are doubts - we check the work with the help of a working memory chip.
in your case, if the memory chip is installed in the adapter - the chip is dead. If chip is samsung - try to use testpoint metod.

MuhammadAbrar

Connection status: EHCI:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-6938
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... CLK, CMD, DAT0 not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 2.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
--- Try to use 1 bit connection ---
plz help

YasirGsm

MuhammadAbrar Connection status: EHCI:HUB:USB 2.00 High-Speed
Interface: UFI High-Speed
Serial number: 0011-8839-6938
Boot version: 1.04, FW version: 1.10 (Mar 26 2017 14:24:34)
Insertion test... CLK, CMD, DAT0 not properly connected
Init bus...
VCC: 3.3 V, VCCQ: 2.8 V
Failed to initialize eMMC (return code: 17, CMD Error: Timeout) !!!
CMD1 error, cmd response: 0x0, card state: 255 (Card is in unknown state)
SEND_OP_COND command failed.
--- Check eMMC pins and connection ---
--- Try to select correct VCC/VCCQ manually ---
--- Try to decrease the clock speed ---
--- Try to use 1 bit connection ---
plz help

emmc not contct dis err help

madgoeslim

YasirGsm Try with this methode : https://ufixers.com/d/101-new-ufi-emmc-adapter-not-properly-connected.

SitunNayak

Cdm error time out

Alexid7

Jamil ???????????????????????????????????